Net price: €152.63
Description
| Technical data | |
|---|---|
| Nominal diameter d1 mm | M52 |
| Thread pitch P mm | 1.5 mm |
| Overall length l1 | 140 mm |
| Flute length l2 | 30 mm |
| Shank diameter d2 | 40 mm |
| Square drive size a | 32 mm |
| Tap drill diameter | 50.5 mm |
| Thread angle G | 60° |
| Tap tolerance | ISO2 6H |

Division of work in the 1–2 set
The M52x1.5 thread is cut into the wall of a hole with a diameter of 50.5 mm. The thread groove extends 0.75 mm into the wall. A single tap would have to cut the entire groove at once, requiring substantial hand torque and risking breakage. The set divides this work into two passes.
The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 8 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.
| Tap | Chamfer | Chamfer angle | Material removed | How it works in the hole |
|---|---|---|---|---|
| No. 1 – roughing tap | long, 8 threads | 5° | the main portion of the groove | enters smoothly and establishes thread alignment |
| No. 2 – finishing tap | short, 2 threads | 20° | the remainder, to the full profile | follows the cut threads and produces the full 6H profile |
The chamfer on No. 1 is 4 times as long as the chamfer on No. 2 — the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.
Hand tapping step by step
Drill bit 50.5 mm
Chamfer 8 threads
Chamfer 2 threads
Tolerance 6H
Turning sequence: half a turn clockwise, a quarter turn counterclockwise | Between taps: remove chips from the hole
Start with the hole. The drill diameter is easy to calculate: thread diameter 52 mm minus pitch 1.5 mm gives 50.5 mm. An undersized hole is a common cause of a tap twisting off in the workpiece.
The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 130 mm, or 2.5 times the thread diameter (2.5 x 52 mm, shown as 2.5D in the drawing). Drill the hole deeper than the thread. The finishing tap has a chamfer spanning 2 threads, so approx. 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates them along with the chips.
Fit the roughing tap in the tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. Turn half a turn clockwise, then a quarter turn counterclockwise. Reversing breaks the chip into short pieces – a slight crunch is normal. The first threads determine whether the thread will be straight.
Back out the roughing tap and remove chips from the hole. Screw the finishing tap into the cut threads by hand – it should engage them on its own. Continue turning at the same rhythm as with the roughing tap. The finishing tap removes the remaining material and cuts the groove to the full profile within tolerance 6H. When it screws in smoothly all the way, the thread is complete – check it with an M52x1.5 screw.
M52X1.5 Hand Tap ISO 529/2 6H HSS is used to cut M52 metric fine threads with a pitch of one and a half millimeters in structural steels with strengths up to eight hundred megapascals. The two-piece operating arrangement — roughing and finishing taps — stabilizes the cutting process, balances loads, and helps maintain a class six H fit.
Design parameters: nominal diameter fifty-two millimeters; pitch one and a half millimeters; sixty° profile according to ISO 68-1; internal thread tolerance class 6H according to ISO 965; right-hand thread; straight flutes for predictable chip evacuation. Precision-ground high-speed steel (HSS) reduces microchipping and maintains edge smoothness. Recommended tap drill: fifty and a half millimeters; cooling with emulsion or active cutting oil improves surface quality and extends cutting edge life.
Compliance with ISO 529/2 (construction), ISO 68-1 (profile geometry), and ISO 965 (class 6H tolerances) guarantees compatibility with inspection instruments, while using M52x1.5 Hand Tap Set further supports repeatable results in one-off and small-batch production.

The set consists of two taps — a roughing tap and a finishing tap, which guarantee a fully formed thread when used in sequence.
High-speed steel (HSS) provides high durability, abrasion resistance, and stable operation even under demanding conditions.
The HSS tool works well in low-carbon steel, aluminum, brass, and other materials with good machinability.
Reference: 096382 In stock < 10 items
€184.50 brutto
Reference: 10540 In stock < 10 items
€155.37 brutto
No customer reviews for the moment.
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Użyj strzałek, aby zmieniać zdjęcia. Powiększaj przyciskami albo gestem szczypania. Zamknij galerię klawiszem Escape.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.