- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Hand Tap M30X3 ISO 529/2 6H HSS
835195
Thread size: M30x3172 sizes of this tap
M1x0,2M1,2x0,2M1,4x0,2M1,6x0,2M1,7x0,2M1,8x0,2M2x0,25M2,2x0,25M2,2x0,35M2,3x0,25M2,3x0,35M2,5x0,35M3x0,35M3,5x0,35M4x0,5M4,5x0,5M5x0,5M5,5x0,5M6x0,5M6x0,75M7x0,5M7x0,75M8x0,5M8x0,75M8x1M9x0,5M9x0,75M9x1M10x0,5M10x0,75M10x1M10x1,25M11x0,75M11x1M11x1,25M12x0,5M12x0,75M12x1M12x1,25M12x1,5M13x1M13x1,25M14x0,75M14x1M14x1,25M14x1,5M15x1M15x1,5M16x0,75M16x1M16x1,25M16x1,5M17x1M17x1,5M17x2M18x0,75M18x1M18x1,25M18x1,5M18x2M19x1M19x1,5M20x0,75M20x1M20x1,25M20x1,5M20x2M21x1,5M22x1M22x1,25M22x1,5M22x1,75M22x2M24x1M24x1,5M24x2M25x1M25x1,5M25x2M26x1M26x1,25M26x1,5M26x2M27x1M27x1,5M27x2M28x1M28x1,5M28x2M30x1M30x1,5M30x2M30x2,5M30x3M32x1,5M32x2M32x3M33x1,5M33x2M33x3M34x1,5M34x2M35x1,5M36x1M36x1,5M36x2M36x3M38x1,5M38x2M38x3M39x1M39x1,5M39x2M39x3M40x1,5M40x2M40x3M42x1,5M42x2M42x3M42x4M45x1,5M45x2M45x3M45x4M46x1,5M46x2M48x1,5M48x2M48x3M48x4M50x1,5M50x2M50x3M52x1M52x1,5M52x2M52x3M52x4M55x2M55x3M56x1,5M56x2M56x3M56x4M58x2M58x4M60x1,5M60x2M60x3M62x1,5M62x2M62x3M62x4M64z1,5M64x2M65x2M65x4M68x1,5M68x2M68x3M68x4M70x1,5M70x2M72x1,5M72x4M75x1,5M75x2M76x1,5M80x1,5M85x2M90x2
€58.26 tax inc.
Net price: €47.37
Description
Technical data for the M30x3 hand tap
| Technical data | |
|---|---|
| Nominal diameter d1 mm | M30 |
| Thread pitch P mm | 3 mm |
| Overall length l1 | 138 mm |
| Flute length l2 | 48 mm |
| Shank diameter d2 | 20 mm |
| Square drive size a | 16 mm |
| Tap drill diameter | 27 mm |
| Thread angle G | 60° |
| Tap tolerance | ISO2 6H |
Roughing tap and finishing tap – how much material each removes
Division of work in the 1–2 set
The M30x3 thread is cut into the wall of a hole with a diameter of 27 mm. The thread groove extends 1.5 mm into the wall. A single tap would have to cut the entire groove at once, requiring substantial hand torque and risking breakage. The set divides this work into two passes.
The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 8 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.
| Tap | Chamfer | Chamfer angle | Material removed | How it works in the hole |
|---|---|---|---|---|
| No. 1 – roughing tap | long, 8 threads | 5° | the main portion of the groove | enters smoothly and establishes thread alignment |
| No. 2 – finishing tap | short, 2 threads | 20° | the remainder, to the full profile | follows the cut threads and produces the full 6H profile |
How to distinguish the taps in the set
The chamfer on No. 1 is 4 times as long as the chamfer on No. 2 — the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.
How to tap an M30x3 hole – sequence 1, 2
Hand tapping step by step
Thread M30x3 in four steps
ØDrilling
Drill bit 27 mm
1Roughing tap
Chamfer 8 threads
2Finishing tap
Chamfer 2 threads
✓Finished thread
Tolerance 6H
Turning sequence: half a turn clockwise, a quarter turn counterclockwise | Between taps: remove chips from the hole
Start with the hole. The drill diameter is easy to calculate: thread diameter 30 mm minus pitch 3 mm gives 27 mm. An undersized hole is a common cause of a tap twisting off in the workpiece.
Through hole or blind hole – how deep to drill
The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 75 mm, or 2.5 times the thread diameter (2.5 x 30 mm, shown as 2.5D in the drawing). Drill the hole deeper than the thread. The finishing tap has a chamfer spanning 2 threads, so approx. 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates them along with the chips.
No. 1 – the roughing tap establishes thread alignment
Fit the roughing tap in the tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. Turn half a turn clockwise, then a quarter turn counterclockwise. Reversing breaks the chip into short pieces – a slight crunch is normal. The first threads determine whether the thread will be straight.
No. 2 – the finishing tap produces the full profile
Back out the roughing tap and remove chips from the hole. Screw the finishing tap into the cut threads by hand – it should engage them on its own. Continue turning at the same rhythm as with the roughing tap. The finishing tap removes the remaining material and cuts the groove to the full profile within tolerance 6H. When it screws in smoothly all the way, the thread is complete – check it with an M30x3 screw.
M30x3 fine-thread hand taps
Hand Tap M30x3 ISO 529/2 6H HSS is used to produce M30 metric fine threads with a pitch of three millimeters in structural steels and metal alloys with tensile strengths up to eight hundred megapascals. The two-piece design — starter tap (I) and finishing tap (II) — distributes torsional loads evenly, stabilizes the machining process, and maintains a fit in class six H.
Technical specifications: nominal diameter thirty millimeters; pitch three millimeters; sixty° profile according to ISO 68-1; internal thread tolerance zone 6H according to ISO 965; right-hand thread; straight flutes for predictable chip evacuation. Ground high-speed steel (HSS) construction reduces microchipping and maintains edge sharpness. Compliance with ISO 529/2 defines the operating sequence, while the order of passes and tool selection are supported by M30x3 Hand Tap Set. Recommended tap drill: twenty-seven millimeters; using an emulsion or active cutting oil extends cutting edge life and improves thread root quality.
- Stable guidance — the two-stage process reduces torque fluctuations and promotes uniform profile formation.
- Operational durability — precision-ground high-speed steel (HSS) maintains low edge roughness and reduces abrasive wear.
- Fit precision — the 6H tolerance enables successful verification with GO / NO-GO gauges.
- Workflow organization — consistent operation and repeatable results are ensured by M30x3 Hand Tap Set.
Reference to ISO 529/2, ISO 68-1, and ISO 965 ensures compatibility with inspection equipment, while the resulting threads maintain a stable profile and predictable parameters in one-off and short-run production.
Stages of cutting an M30x3 thread with a 2-piece set: roughing tap and finishing tap
Frequently asked questions
The set consists of two taps — a roughing tap and a finishing tap, which guarantee a fully formed thread when used in sequence.
Drill to 27 mm (nominal diameter 30 mm minus pitch 3 mm) to achieve proper thread engagement in class 6H.
Chamfer the entry to 1×45°, use a tapping oil suited to the material, maintain alignment with a guided tap wrench, and break chips regularly with short reverse turns.
Product accessories
Tapered countersink 37/90 DIN 335 C HSS
Reference: 0000004108 In stock > 10 items
€32.11
€39.49 brutto
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
Viewed products
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.