- 98% satisfied customers
- 72h delivery
- 14 days to return
Polski
English
check
Machine taps - Fanar - Technical articles
The presented category includes a wide selection of machine threaders, designed for machine processing of all types of threads and materials.
Offer of high-performance machine taps
We offer you machine thread ers only from the best European manufacturers, so that they are a combination of the highest quality and at the same time at an affordable price.
The offered threaders are made by Fanar Ciechanow, Narex from the Czech Republic and Fra from Serbia. In our offer we have metric machine threaders, ordinary as well as fine-coil, inch threaders G, unified American UNC and fine-coil UNF, Whitowrtha such as BSW and BSF as well as metric trapezoidal threaders. A full range of taps means that these tools are in our stock so that they would be available to you within 24H of your order.
High-performance machine taps are produced in two versions of the cutter: C straight or torsion cutter and B straight cutter. Cut C straight is designed for both through-holes and blind holes. Nut C torsion is designed for blind holes, torsion grooves lead the chips up the hole. The B nut is suitable for tapping through holes. The notch, which is located at the beginning of the tapping tool, breaks the chip and pushes it down the hole.
Metric machine taps are tools that have a thread dimension measured in metric units [mm]. They come in M metric plain threads and MF metric fine threads. Metric machine threads have an angle of outline of 60 degrees and come in standard sizes from M3 to M52. With ordinary metric taps, the pitch is not specified, only when the thread is fine thread. Metric taps come in dimensional versions with a thinner through-shank DIN 376, and DIN 374 as well as a thicker shank DIN 371.
Inch G machine t aps come in DIN 5156, which is a standard with a neck thinner than the working part, which makes it possible to thread deep holes. They have a thread angle of 55 degrees and are measured in units of inches ( 1 inch-25.4 mm). Another inch machine threaders are UNC and UNF unified machine threaders. These are typical American taps, their fine-twist variety is used in thin-walled connections where there is no room for too much thread depth.
Construction of a machine tapping machine
Machine taps are already produced mainly from HSSE cobalt high-speed steel ( 5% cobalt content ) and most often then the taps have the Inox mark. The Inox mark informs about the possibility of threading in materials such as steel, stainless steel and cast iron. All these materials should not have a higher tensile strength like Rm=800 Mpa. Other threaders that are used for HSSE-PM powder steel threaders and VHM solid carbide threaders.
In our offer you will also find tapered countersinks for threads.
Division of machine taps by purpose
Machine taps differ from each other in terms of the applied nuts, chip grooves and shanks. And by purpose we can divide them into:
- taps for blind holes,
- taps for through holes.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
| Cookie | Provider | Purpose | Expiry |
|---|---|---|---|
| PHP_SESSID | artykulytechniczne.pl | The PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser. | Session |
| PrestaShop-# | artykulytechniczne.pl | This is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop. | 480 hours |
| rc::a | It is used to read and filter bot requests. | Persistent | |
| rc::c | It is used to read and filter bot requests. | Persistent |
| Cookie | Provider | Purpose | Expiry |
|---|---|---|---|
| ads/ga-audiences | These cookies are used by Google AdWords to re-engage visitors that are likely to convert to customers based on the visitor’s online behaviour across websites. | Session |
| Cookie | Provider | Purpose | Expiry |
|---|---|---|---|
| _ga | Registers a unique ID that is used to generate statistical data on how the visitor uses the website. | 2 years | |
| _gat | Used by Google Analytics to throttle request rate | 1 day | |
| _gd# | This is a Google Analytics Session cookie used to generate statistical data on how you use the website which is removed when you quit your browser. | Session | |
| _gid | Registers a unique ID that is used to generate statistical data on how the visitor uses the website. | 1 day |