- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Description
DIAMETER Ø35.5 mm
MORSE TAPER MT4
OVERALL LENGTH 339 mm
FLUTE LENGTH 190 mm
Technical specifications of the Ø35.5 mm drill bit
Twist drill with Morse taper shank
| TECHNICAL DATA | |
|---|---|
| Diameter | Ø35.5 NWKc HSSE |
| Standard | DIN 345 |
| Drill type | NWKc — twist drill with taper shank |
| Material | HSSE (cobalt high-speed steel) |
| Overall length l1 | 339 mm |
| Flute length l2 | 190 mm |
| Morse taper | MT4 |
| Point angle | 118° |
| Diameter tolerance | h8 |
| Cutting direction | Right-hand |
Ø35.5 mm HSSE twist drill – MT4 Morse taper
Product description and key benefits
The Ø35.5 mm metal drill bit with an MT4 Morse taper is a large-diameter tool whose mechanical loads require an MT4 taper with a diameter of 31.27 mm. At Ø35.5, torque in S355 steel is high enough to require a rigid machine base. The Ø35.5 Morse taper drill bit can operate at full speed only with abundant emulsion cooling and power spindle feed.
Key benefits of the Ø35.5 mm metal drill bit
- HSSE steel with 5% cobalt — heat resistance up to 650°C allows drilling in 304/316 stainless steels without rapid dulling of the cutting edge
- Morse taper MT4 — self-holding mounting in the spindle eliminates slippage at the high cutting torques generated in difficult-to-machine steels
- Increased hot hardness — cobalt in the steel matrix increases resistance to tempering — essential at low Vc and the high cutting resistance of austenitic steels
- DIN 345 — full interchangeability with HSS drills of the same size and compatibility with reduction sleeves
- Flute length 190 mm — drilling through holes in components up to 175 mm thick
- Machining INOX steel without coatings — HSSE geometry and composition allow drilling in acid-resistant steels without TiN/TiAlN coatings
The Ø35.5 Morse taper drill is chosen for heavy-duty hole machining in machine building, ship repair yards, and valve and fitting factories. Typical applications: holes in end plates, bearing end shields, and drive components. Hole tolerance class H12 (Ø35.500–Ø35.750 mm); tighter fits are achieved by boring.
Morse tapers – dimensions to DIN 228
Dimension table for all Morse tapers MT0–MT6
| Taper | Diameter D [mm] | Length [mm] |
|---|---|---|
| MT0 | 9.045 | 49.8 |
| MT1 | 12.065 | 53.5 |
| MT2 | 17.780 | 64.0 |
| MT3 | 23.825 | 80.5 |
| MT4 | 31.267 | 117.5 |
| MT5 | 44.399 | 149.5 |
| MT6 | 63.348 | 210.0 |
REDUCTION SLEEVES COMPATIBLE WITH THE Ø35.5 MM DRILL BIT:
| ✓ | MT4 → MT5 — for a spindle with an MT5 socket |
| ✓ | MT4 → MT3 — for a spindle with an MT3 socket |
| ✓ | MT4 drill drift — for removing the drill bit from the spindle |
Cutting data for the Ø35.5 mm drill bit according to ISO 513
Recommended machining conditions for a diameter of Ø35.5 mm
| ISO symbol | Workpiece material | Vc [m/min] | f [mm/rev] | n [rpm] | Vf [mm/min] |
|---|---|---|---|---|---|
| P Steel | Structural steel up to 900 N/mm² | 11÷20 | 0.25 | 99÷179 | 25÷45 |
| K Cast iron | Gray cast iron GG20–GG30 | 13÷16 | 0.25 | 117÷143 | 29÷36 |
| N Copper and Al alloys | Cu, CuZn, Al, and alloys | 25÷28 | 0.32÷0.40 | 224÷251 | 72÷100 |
Minimum machine tool power
The Ø35.5 mm drill requires a drilling machine with at least 2.2 kW of power and power spindle feed. Stability is difficult to maintain with manual feed — uneven pressure leads to vibration and accelerated cutting edge wear. A box-column or radial drilling machine is recommended.
Material compatibility of the Ø35.5 mm drill bit
Range of workpiece materials and application limitations
✓ Structural steel (S235, S355) up to 900 N/mm²
✓ Gray and ductile cast iron (GG20, GGG40)
✓ Low-carbon and medium-alloy steel
▲ Stainless steel (Vc reduced by 30%, ample coolant)
▲ Aluminum and Al alloys (emulsion coolant required)
✗ Hardened steels above 45 HRC
Frequently asked questions about the Ø35.5 mm drill bit
1) Clean the taper and spindle socket. 2) Check runout (maximum 0.03 mm). 3) Replace the drill if the taper is damaged or worn. 4) Do not stack reduction sleeves (e.g., MT4→MT3→MT5).
For diameters up to approximately 40 mm, drilling into solid material is possible after spot drilling with an NC 90° drill. Above 40 mm, a Ø20–25 mm pilot hole is recommended to reduce axial force by 40–50% and eliminate vibration from the chisel edge.
When drilling S355 steel with a Ø35.5 mm drill, the torque is approximately 88 Nm. This requires a drilling machine with a minimum power rating of 2.1 kW and power spindle feed.
Product accessories
Reduction sleeve MK6 MK4 1751 PTPa DIN 228
Reference: 1186 In stock < 10 items
€36.84
€45.32 brutto
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.