- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Description
DIAMETER Ø36 mm
MORSE TAPER MT4
OVERALL LENGTH 344 mm
FLUTE LENGTH 195 mm
Technical specifications of the Ø36 mm drill bit
Twist drill with Morse taper shank
| TECHNICAL DATA | |
|---|---|
| Diameter | Ø36 NWKc HSSE |
| Standard | DIN 345 |
| Drill type | NWKc — twist drill with taper shank |
| Material | HSSE (cobalt high-speed steel) |
| Overall length l1 | 344 mm |
| Flute length l2 | 195 mm |
| Morse taper | MT4 |
| Point angle | 118° |
| Diameter tolerance | h8 |
| Cutting direction | Right-hand |
Ø36 mm HSSE twist drill – MT4 Morse taper
Product description and key benefits
The Ø36 mm twist drill is an industrial NWKc cutting tool designed for drilling large-diameter holes in structural and alloy steels. The MT4 Morse taper shank provides rigid, self-holding mounting in the spindle — without the risk of slipping at maximum cutting torque. The Ø36 Morse taper drill is suitable for pillar and box-column drilling machines used in industrial facilities.
Key benefits of the Ø36 mm metal drill bit
- HSSE steel with 5% cobalt — heat resistance up to 650°C allows drilling in 304/316 stainless steels without rapid dulling of the cutting edge
- Morse taper MT4 — self-holding mounting in the spindle eliminates slippage at the high cutting torques generated in difficult-to-machine steels
- Increased hot hardness — cobalt in the steel matrix increases resistance to tempering — essential at low Vc and the high cutting resistance of austenitic steels
- DIN 345 — full interchangeability with HSS drills of the same size and compatibility with reduction sleeves
- Flute length 195 mm — drilling through holes in components up to 180 mm thick
- Machining INOX steel without coatings — HSSE geometry and composition allow drilling in acid-resistant steels without TiN/TiAlN coatings
The Ø36 Morse taper drill is chosen for heavy-duty hole machining in machine building, ship repair yards, and valve and fitting factories. Typical applications: holes in end plates, bearing end shields, and drive components. Hole tolerance class H12 (Ø36.000–Ø36.250 mm); tighter fits are achieved by boring.
Morse tapers – dimensions to DIN 228
Dimension table for all Morse tapers MT0–MT6
| Taper | Diameter D [mm] | Length [mm] |
|---|---|---|
| MT0 | 9.045 | 49.8 |
| MT1 | 12.065 | 53.5 |
| MT2 | 17.780 | 64.0 |
| MT3 | 23.825 | 80.5 |
| MT4 | 31.267 | 117.5 |
| MT5 | 44.399 | 149.5 |
| MT6 | 63.348 | 210.0 |
REDUCTION SLEEVES COMPATIBLE WITH THE Ø36 MM DRILL BIT:
| ✓ | MT4 → MT5 — for a spindle with an MT5 socket |
| ✓ | MT4 → MT3 — for a spindle with an MT3 socket |
| ✓ | MT4 drill drift — for removing the drill bit from the spindle |
Cutting data for the Ø36 mm drill bit according to ISO 513
Recommended machining conditions for a diameter of Ø36 mm
| ISO symbol | Workpiece material | Vc [m/min] | f [mm/rev] | n [rpm] | Vf [mm/min] |
|---|---|---|---|---|---|
| P Steel | Structural steel up to 900 N/mm² | 11÷20 | 0.25 | 97÷177 | 24÷44 |
| K Cast iron | Gray cast iron GG20–GG30 | 13÷16 | 0.25 | 115÷141 | 29÷35 |
| N Copper and Al alloys | Cu, CuZn, Al, and alloys | 25÷28 | 0.32÷0.40 | 221÷248 | 71÷99 |
Cooling for large diameters
At a diameter of 36 mm, the volume of chips generated per centimeter of depth is approximately 10.2 cm³. Use a 6–8% emulsion at a minimum flow rate of 6 l/min. Without pressurized cooling, limit the depth per pass to 54 mm.
Material compatibility of the Ø36 mm drill bit
Range of workpiece materials and application limitations
✓ Structural steel (S235, S355) up to 900 N/mm²
✓ Gray and ductile cast iron (GG20, GGG40)
✓ Low-carbon and medium-alloy steel
▲ Stainless steel (Vc reduced by 30%, ample coolant)
▲ Aluminum and Al alloys (emulsion coolant required)
✗ Hardened steels above 45 HRC
Frequently asked questions about the Ø36 mm drill bit
Depth greater than 3×D (108 mm): reduce feed by 30–50%, retract every 1×D, and use a 6–8% emulsion at a minimum flow rate of 6 l/min. Peck drilling prevents chips from jamming in the flutes.
1) Clean the taper and spindle socket. 2) Check runout (maximum 0.03 mm). 3) Replace the drill if the taper is damaged or worn. 4) Do not stack reduction sleeves (e.g., MT4→MT3→MT5).
For diameters up to approximately 40 mm, drilling into solid material is possible after spot drilling with an NC 90° drill. Above 40 mm, a Ø20–25 mm pilot hole is recommended to reduce axial force by 40–50% and eliminate vibration from the chisel edge.
Product accessories
Reduction sleeve MK6 MK4 1751 PTPa DIN 228
Reference: 1186 In stock < 10 items
€36.84
€45.32 brutto
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
Viewed products
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.