Polski 
- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Adjustable reamer 9.5-10.25 mm NRZe
15024
€25.89 tax inc.
Net price: €21.05
Description
Adjustable reamer 9.5-10.25 mm – reamer adjustable to 10 mm
Technical data – HSS blades, shank with square drive for a tap wrench
| Technical data | |
|---|---|
| Adjustment range | 9.5–10.25 mm |
| Designation | NRZe to PN |
| Blades | HSS, in inclined grooves |
| Diameter adjustment | two nuts |
| Shank diameter | 5.7 mm |
| Shank square | 4.5 mm |
| Overall length | 124 mm |
| Blade length | 40 mm |
| Drive | tap wrench |
Adjustable reamer 9.5-10.25 mm The NRZe finishes holes from 9.5 to 10.25 mm, including the full 10 mm size. Set the diameter with two nuts that move the high-speed steel (HSS) blades along inclined grooves in the body. For a 10 mm hole, use a 9.9 mm straight shank drill bit. The reamer removes the 0.1 mm allowance in one pass. Operate it by hand with a tap wrench fitted over the square on the shank.
Manufacturers design adjustable blade reamers for repair and assembly work. They are useful wherever a hole needs to be fitted to the part at hand. The diameter is then set to the size of the part, rather than to the standard size series of fixed reamers.
Which size to choose: 9.5-10.25 mm and adjacent sizes
Below 9.5 mm, use the 8.7-9.5 mm reamer; above 10.25 mm, use the 10.25-11 mm reamer. The 9.7-10.5 mm reamer also covers holes from 9.7 to 10.25 mm. The 10.25-11 mm reamer has a larger square: 4.8 mm compared with 4.5 mm on this model. The 4.5 mm square still fits a No. 0 tap wrench, designed for squares from 2 to 5 mm.
How diameter adjustment works – blades and two nuts
NRZe reamer construction and measuring the diameter setting
The body has inclined grooves around its circumference, each holding an HSS blade. Two nuts, front and rear, retain the blades at both ends. Moving the blades along the grooves moves their cutting edges away from or toward the axis. This changes the cutting diameter over a range of 0.75 mm, from 9.5 to 10.25 mm. This is why the tool is also called an adjustable reamer.
Adjustment in three steps
First, loosen one nut. Then tighten the other — the blades will move to the new diameter. Finally, lock the blades by tightening the first nut. The rear nut, on the shank side, provides the main clamping force; the front nut is only snugged up. Tighten carefully. Excessive force bows the blades outward and causes the reamer to catch in the hole.
How to measure the set diameter
With an even number of blades, measure the diameter across two opposite blades using a micrometer. With an odd number, a groove lies opposite each blade, so the micrometer will read too low. In this case, use a setting ring or a hole of known diameter. Insert the reamer and expand the blades until they contact the hole wall.
How to ream step by step – tap wrench and clockwise rotation
Guidelines for using an adjustable hand reamer
Insert the reamer into the hole and apply light pressure so the blades engage the wall immediately. The tap wrench must fit the square closely to ensure smooth rotation without jerking. Align the reamer axis with the hole axis. For a longer hole, check the alignment with a square.
Hand reaming in six steps
1
Drill a hole
0.05–0.15 mm smaller than the finished hole, e.g., 9.7 mm for 9.8 mm.
2
Set the diameter
Loosen one nut, move the blades with the other, then lock the first nut.
3
Fit the tap wrench
Fit it to the square and align the reamer with the hole axis.
4
Turn clockwise
Turn smoothly with light, even pressure.
5
Withdraw the reamer
Keep turning clockwise, including as the blades leave the hole.
✓
Check the hole
Too tight? Set a larger diameter and make a second pass.
Guidelines based on adjustable reamer manufacturers' instructions.
As the blades emerge from the far end of the hole, resistance drops suddenly. Reduce pressure at this point, but maintain the same turning speed. Otherwise, the reamer will jump through the end of the hole and leave it uneven.
▲
Never turn counterclockwise
Turning counterclockwise in the hole dulls the blades and may chip them. It can also loosen a nut and change the setting. Turn clockwise when withdrawing the tool as well; otherwise, you will scratch the hole wall.
How much material one pass removes
Reaming allowance and drill bit selection
This tool finishes a hole rather than drilling it. It removes a thin layer: 0.05 to 0.15 mm on diameter in one pass. A smaller allowance produces a smoother hole wall. Too little allowance is detrimental because the blades rub against the wall instead of cutting and dull faster. The drawing shows a 9.8 mm hole after a 9.7 mm drill.
Calculation: 10 mm hole after drilling with a 9.9 mm drill bit
Allowance on diameter = finished hole diameter 10.0 mm − drill diameter 9.9 mm = 0.1 mm. Half of this, or 0.05 mm, is on each wall. This layer is thinner than a sheet of paper. A reamer set to 10.0 mm will remove it in one pass.
| Finished hole [mm] | Drill bit [mm] | Diametral allowance [mm] | Layer thickness at the wall [mm] | Passes |
|---|---|---|---|---|
| 9.5 | 9.4 | 0.1 | 0.05 | 1 |
| 9.8 | 9.7 | 0.1 | 0.05 | 1 |
| 10.0 | 9.9 | 0.1 | 0.05 | 1 |
| 10.25 | 10.1 | 0.15 | 0.075 | 1 |
The upper limit of 10.25 mm has two decimal places. A 10.1 mm drill bit leaves 0.15 mm for this size, the maximum the blades can remove in one pass. A 10.2 mm drill bit leaves 0.05 mm, the minimum allowance at which the blades still cut.
Tap wrench and lubrication – what to prepare
Tap wrench for a 4.5 mm square and oil suited to the material
Tap wrench No. 0
The shank square measures 4.5 mm. Select an adjustable tap wrench to DIN 1814, size No. 0. It accommodates squares from 2 to 5 mm and fits M1–M8 taps.
With oil or dry
| Workpiece material | Lubrication |
|---|---|
| Steel and cast steel | cutting oil or emulsion |
| Aluminum alloys | cutting oil or emulsion |
| Gray and malleable cast iron | dry |
| Bronze and brass | dry |
Remove chips from the reamer after use. Before adjusting the blades, also clean the body grooves so the blades move evenly.
Adjustable reamer 9.5-10.25 mm The NRZe covers the full 10 mm size, and the hole can be prepared with a 9.9 mm drill bit. The reamer is 124 mm long, and its blades are 40 mm long. The shank square measures 4.5 mm and fits a No. 0 tap wrench. The blades remove the 0.1 mm allowance in one pass. Always turn the reamer clockwise, including when withdrawing it.
Questions about drill bits, size selection, and operation
Frequently asked questions about hand reaming
With a 9.9 mm straight shank drill to DIN 338. This leaves an allowance of 0.1 mm on diameter. A reamer set to 10.0 mm will remove it in one pass.
Three reamers cover a 10.25 mm hole: this model, the 9.7-10.5 mm model, and the 10.25-11 mm model. Prepare it with a 10.1 or 10.2 mm drill bit. The 0.15 or 0.05 mm allowance can be removed in one pass.
Clockwise, just as when reaming. Clockwise rotation protects the blades and the hole wall. It also keeps the nuts in place, so the setting does not change.
Yes, at very low speed and with plenty of oil. At high speed, the hole may end up larger than the setting. Using a tap wrench provides the best control.
Product accessories
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.