• 98% satisfied customers
  • 72h delivery
  • 30 dni na zwrot
Hand reamer 6.5 H7 NRTh DIN 206 HSS
search
  • Hand reamer 6.5 H7 NRTh DIN 206 HSS
  • Hand reamer 6.5 H7 NRTh DIN 206 HSS - nr. 1

Hand reamer 6.5 H7 NRTh DIN 206 HSS

351969
€11.33 tax inc.

Net price: €9.21

Brak w magazynie
Brak w magazynie

Call and order: (44) 755-04-05

Description

Cutting diameter DØ6.5 H7hole 6.500–6.515 mm
MaterialHSShigh-speed steel (HSS)
StandardDIN 206hand reamer
Number of cutting edgesZ = 6straight flutes

Technical data for the 6.5 H7 hand reamer

dimensions, standard, and shank specifications

Technical data
Cutting diameter DØ6.5 H7 · hole 6.500–6.515 mm
Hole tolerance zoneH7 (+0.015 / 0 mm)
TypeFixed-size shank-type hand reamer
Dimensional standardDIN 206
MaterialHSS (high-speed steel)
Flute length l50 mm
Shank length l₁36 mm
Overall length L100 mm
Number of cutting edges Z6 (straight flutes)
Shank / driveStraight shank with square drive (for a tap wrench)
Hand reamer 6.5 H7 NRTh DIN 206 in HSS — shank-type finishing reamer for cylindrical holes with a square drive for a tap wrench

Hand reamer 6.5 H7 NRTh — characteristics

construction, operation, and applications

Fixed-size, shank-type hand reamer 6.5 H7 NRTh to DIN 206 finishes cylindrical Ø6.5 holes. It brings them to grade H7 (6.500–6.515 mm), removing a thin layer of a few hundredths of a millimeter from the wall — the hole achieves an accurate size, better roundness, and lower roughness.

The reamer is made of high-quality Polish-made high-speed steel (HSS). A set of 6 straight cutting edges distributes cutting forces over multiple edges, maintaining hole roundness and avoiding the vibration typical of a two-lip drill. The tapered lead guides the tool concentrically into the pilot hole, while the straight shank ending in a square drive engages with a tap wrench.

This is a machining operation for finishing operation, not roughing. Drilling alone produces a hole of grade IT10–IT11; the reamer is intended to tighten its tolerance to H7 and smooth the wall. Important: the reamer follows the hole and cannot correct misalignment, so drill the pilot hole perpendicularly and on-axis. Unlike the machine version, the hand version has a longer tapered lead and more cutting edges, making it easier to guide under less rigid operating conditions. It is used for locating holes in housings and fixtures, where dimensional repeatability translates into assembly accuracy.

H7 tolerance and Ø6.5 hole accuracy

final tolerance zone of the machined hole

Ø6.5 mm hole size by tolerance grade (ISO 286)

DesignationHole Ø range [mm]Deviations [mm]IT tolerance grade
6.5 H66.500 – 6.509+0.009 / 09 µm
6.5 H76.500 – 6.515+0.015 / 015 µm this product
6.5 H86.500 – 6.522+0.022 / 022 µm
6.5 H96.500 – 6.536+0.036 / 036 µm
6.5 H116.500 – 6.590+0.090 / 090 µm

Your reamer produces tolerance grade H7 — finished hole Ø6.500–6.515 mm; the value is stated directly, without conversion from tables. A narrower tolerance zone means a more accurate hole. The reamed surface is smooth — typically Ra 0.4–1.6 µm, significantly better than after drilling alone (approx. 1.6–3.2 µm).

Manual machining — how to ream Ø6.5 H7

tap wrench operation, allowance and predrilled hole

The reamer is secured in a tap wrench by the square drive of the shank and operated by hand — with steady rotation in one direction and light, even pressure. For reaming to Ø6.5 H7, leave a 0.1–0.2 mm allowance on diameter: drill the pilot hole with a drill of Ø6.3 mm, then ream to the final size. Maintain moderate, even pressure and do not reverse rotation while cutting. Lubricate generously with cutting oil — it reduces cutting resistance and improves the surface finish to Ra 0.4–1.6 µm (drilling alone leaves approximately 1.6–3.2 µm).

▲Important: is a tool for manual machining — it is not intended for powered operation at high speeds. High-speed steel loses hardness above approx. 600 °C, so lubricate generously. Do not stop the reamer in the hole or reverse rotation — always withdraw it while continuing to rotate forward; withdrawing without rotation risks chip jamming, chipped cutting edges and a poorer hole finish.

Applications — workpiece materials

groups P1.2–P1.3 according to the material classification

✓Unalloyed and structural steel
✓Free-machining steel
✓Nonferrous metals — brass, bronze, copper
✓Light alloys and soft metals
▲Alloy steel — possible with generous lubrication and low speeds
✗Hardened steel and hardened stainless steel — beyond the capabilities of HSS

Frequently asked questions

Unalloyed and free-machining steel, nonferrous metals (brass, bronze, copper), and light alloys — materials in group P1.2–P1.3. The HSS cutting edges provide durability during hand operation, but the tool is not intended for hardened steel or hardened stainless steel.

It means the hole is produced within 6.500–6.515 mm — upper deviation +0.015 / 0 mm, without falling below the nominal size. Reaming also produces a smooth wall with Ra 0.4–1.6 µm.

Yes — drill Ø6.3 mm, leaving a stock allowance of 0.1–0.2 mm on the diameter. The reamer is a finishing tool and removes only a thin layer; it cannot replace drilling from solid.

Product accessories

Tap wrench No. 1,5

Reference: 0000008974 In stock > 10 items

€4.47

€5.50 brutto

Reviews

No customer reviews for the moment.

Add a review about the product

Hand reamer 6.5 H7 NRTh DIN 206 HSS

Hand reamer 6.5 H7 NRTh DIN 206 HSS

Shipping

All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE

Courier GLS Przelew24 / Prepayment 14,76 zł gross Delivery time 1 working day
Courier GLS Cash on delivery 17,26 zł gross Lead time 1 working day

This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

More information