• 98% satisfied customers
  • 72h delivery
  • 30 dni na zwrot
Hand reamer fi 20 H7 DIN 206 HSSE
search
  • Hand reamer fi 20 H7 DIN 206 HSSE
  • Hand reamer fi 20 H7 DIN 206 HSSE - nr. 1

Hand reamer 20 H7 NRTh DIN 206 HSS

1231
€71.21 tax inc.

Net price: €57.89

Instant Shipping
W magazynie: 10-100 szt.
W magazynie: 10-100 szt.

Instant Shipping

Call and order: (44) 755-04-05

Description

Cutting diameter DØ20 H7hole 20.000–20.021 mm
MaterialHSShigh-speed steel (HSS)
StandardDIN 206hand reamer
Number of cutting edgesZ = 10straight flutes

Technical data for the 20 H7 hand reamer

dimensions, standard, and shank specifications

Technical data
Cutting diameter DØ20 H7 · hole 20.000–20.021 mm
Hole tolerance zoneH7 (+0.021 / 0 mm)
TypeFixed-size shank-type hand reamer
Dimensional standardDIN 206
MaterialHSS (high-speed steel)
Flute length l100 mm
Shank length l₁74 mm
Overall length L201 mm
Number of cutting edges Z10 (straight flutes)
Shank / driveStraight shank with square drive (for a tap wrench)
Hand reamer 20 H7 NRTh DIN 206 in HSS — shank-type finishing reamer for cylindrical holes with a square drive for a tap wrench

Hand reamer 20 H7 NRTh — characteristics

construction, operation, and applications

Hand reamer 20 H7 NRTh conforming to DIN 206 is a shank-type finishing tool for cylindrical holes. After drilling, it brings a Ø20 hole to the precise tolerance grade H7 (20.000–20.021 mm) — it removes a small allowance around the entire circumference, improving the hole size, roundness and surface finish.

The tool body is made of high-grade high-speed steel (HSS) produced in Poland. The cutting section has straight flutes and 10 cutting edges: more edges distribute cutting forces more evenly, improving hole roundness and reducing vibration compared with a two-edge drill bit. The extended lead taper centers the reamer in the hole, while the square drive on the shank transmits torque from the tap wrench.

Reaming is a finishing operation, not a roughing operation. After drilling, the hole falls within the broad IT10–IT11 tolerance range; the reamer tightens its tolerance to H7, while also improving the wall finish. Note that the tool follows the existing hole and will not straighten a crooked hole — the initial hole must therefore be drilled perpendicular to the surface. Unlike a machine reamer, the hand version has an extended lead taper and more cutting edges, promoting even cutting. It works well in one-off and repair work — when fitting locating pins, where a repeatable, accurate hole is essential.

H7 tolerance and Ø20 hole accuracy

final tolerance zone of the machined hole

Ø20 mm hole size by tolerance grade (ISO 286)

DesignationHole Ø range [mm]Deviations [mm]IT tolerance grade
20 H620.000 – 20.013+0.013 / 013 µm
20 H720.000 – 20.021+0.021 / 021 µm this product
20 H820.000 – 20.033+0.033 / 033 µm
20 H920.000 – 20.052+0.052 / 052 µm
20 H1120.000 – 20.130+0.130 / 0130 µm

Your reamer produces tolerance grade H7 — finished hole Ø20.000–20.021 mm; the value is stated directly, without conversion from tables. A narrower tolerance zone means a more accurate hole. The reamed surface is smooth — typically Ra 0.4–1.6 µm, significantly better than after drilling alone (approx. 1.6–3.2 µm).

Manual machining — how to ream Ø20 H7

tap wrench operation, allowance and predrilled hole

The reamer engages with the tap wrench through the square drive on the shank — guide it by hand, steadily and in one direction, with moderate pressure. For Ø20 H7, leave a 0.2–0.3 mm allowance on diameter; predrill the hole with a drill of Ø19.7 mm, and finish with a reamer. Apply moderate, even pressure and do not reverse the direction of rotation while cutting. Generous lubrication with cutting oil is essential — it reduces resistance and improves the surface finish to Ra 0.4–1.6 µm (approx. 1.6–3.2 µm after drilling).

▲Important: is a tool for manual machining — it is not intended for powered operation at high speeds. High-speed steel loses hardness above approx. 600 °C, so lubricate generously. Do not stop the reamer in the hole or reverse rotation — always withdraw it while continuing to rotate forward; withdrawing without rotation risks chip jamming, chipped cutting edges and a poorer hole finish.

Applications — workpiece materials

groups P1.2–P1.3 according to the material classification

✓Unalloyed and structural steel
✓Free-machining steel
✓Nonferrous metals — brass, bronze, copper
✓Light alloys and soft metals
▲Alloy steel — possible with generous lubrication and low speeds
✗Hardened steel and hardened stainless steel — beyond the capabilities of HSS

Frequently asked questions

Yes — nonferrous metals and light alloys (brass, bronze, copper, aluminum) are among the recommended materials in group P1.2–P1.3, alongside unalloyed and free-machining steels. The limitations are hardened steels and hardened stainless steels, for which HSS is too soft.

The hole size falls within 20.000–20.021 mm (H7, +0.021 / 0 mm), and roughness drops to Ra 0.4–1.6 µm. By comparison, drilling alone leaves approx. 1.6–3.2 µm and a much looser IT10–IT11 tolerance grade.

The optimum diametral allowance is 0.2–0.3 mm. Drill the initial hole with a Ø19.7 mm drill bit; excessive allowance impairs the surface finish and loads the cutting edges, while insufficient allowance will not remove drilling marks.

Product accessories

Reviews

No customer reviews for the moment.

Add a review about the product

Hand reamer 20 H7 NRTh DIN 206 HSS

Hand reamer 20 H7 NRTh DIN 206 HSS

Shipping

All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE

Courier GLS Przelew24 / Prepayment 14,76 zł gross Delivery time 1 working day
Courier GLS Cash on delivery 17,26 zł gross Lead time 1 working day

This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

More information