- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Description
Taper reamer 1:16 — 1 1/2" for NPT pipe threads
Technical specifications · ASME B94.2-1995 standard
TypeTapered 1:16hand reamer
For thread1 1/2" NPT1 1/2 inch · NPTF · Rc
StandardASME B94.2ASME B94.2-1995
MaterialHSShigh-speed steel (HSS) (M2)
| TECHNICAL DATA | |
|---|---|
| Reamer | 1 1/2" NPT (included angle 3.58°) |
| Tip diameter d1 | 43 mm |
| Larger diameter d2 | 45.8 mm |
| Shank diameter d3 | 38 mm |
| Overall length | 105 mm |
| Flute length | 45 mm |
| Square drive | 28.5 mm |
| Intended use | 1 1/2" NPT · NPTF · Rc thread |
| Material | HSS — high-speed steel (grade M2) |
| Standard | ASME B94.2-1995 |
What a 1:16 taper reamer is used for
Preparing a hole for a taper pipe thread
Taper reamer 1:16 in size 1 1/2" is a hand-operated finishing tool that gives a drilled hole a precise 1:16 taper ratio — the same as the American taper pipe thread NPT (National Pipe Taper). The tool is made from high-speed steel (HSS) HSS (grade M2) according to the standard ASME B94.2-1995, and its tapered cutting section transitions smoothly from a diameter of 43 mm at the tip to 45.8 mm at the base. The standard itself ASME B94.2 specifies the dimensions of the reamer, not the thread — compatibility with NPT and Rc threads results from the 1:16 taper geometry itself.
In a threaded pipe connection, the taper provides the seal — the threads press increasingly tightly together as the connection is screwed in. If the thread were cut directly into a cylindrical hole, the pipe tap would have to form the taper and cut the thread profile simultaneously, significantly increasing torque and loading the first threads. The reamer forms the taper beforehand, so the tap only removes material to form the thread profile — evenly, with less resistance, producing a fuller, tighter-sealing thread and longer tap life.
Since the reamer produces only the 1:16 taper ratio, not the thread profile, the same hole can be tapped with different profiles sharing the same taper: NPT and NPTF (Dryseal, metal-to-metal seal, 60° profile), as well as Rc (taper pipe thread according to ISO 7-1, 55° profile). NPT is sometimes called the Briggs thread — after the author of the original standard.
Typical applications:
- Hydraulics and pneumatics — ports for fittings, valves and pressure connections
- Industrial fittings and piping systems — bodies, tees, reducers
- Maintenance and workshop use — repairing and restoring threaded ports
Step-by-step process for cutting a 1 1/2" NPT thread
Drilling → taper reaming → tapping
Three steps to a leak-tight pipe thread
1 Drilling the hole
Ø ~42.8 mm
2 Reaming 1:16
taper 43 → 45.8
3 Tapping
tap 1 1/2"-11.5 NPT
✓ Leak-tight connection
profile NPT / NPTF / Rc
Taper allowance: flute length 45 mm × taper ratio 1/16 = 2.81 mm increase in diameter (43 + 2.81 ≈ 45.8 mm). Pitch of the 1 1/2"-11.5 NPT thread: 25.4 mm ÷ 11.5 = 2.21 mm.
1 1/2" NPT pipe thread specifications
Target thread data — for drill and tap selection
The values below describe the target thread 1 1/2"-11.5 NPT, for which the reamer prepares the hole — these are reference data for selecting the drill and tap, and not specifications of the reamer itself. The reamer determines only the taper ratio 1:16; the pitch, thread count and thread profile angle are produced by the tap.
| Thread / hole parameter | Value |
|---|---|
| Thread designation | 1 1/2"-11.5 NPT |
| Thread count | 11.5 threads per inch (TPI) |
| Thread pitch | 2.21 mm |
| Thread angle | 60° (NPT/NPTF) · 55° (Rc) |
| Taper ratio | 1:16 (3/4" per foot) — the only parameter produced by the reamer |
| Thread major Ø | ~48.3 mm (1.900") |
| Drill Ø with reaming | ~42.8 mm |
| Drill Ø without reaming | 1-23/32" ≈ 43.7 mm |
▲
Match the thread profile to the mating component
The reamer produces only the 1:16 taper ratio — it does not distinguish between thread profiles. Threads NPT (60°) and BSPT/R (55°) are not interchangeable despite having the same taper: they make only point contact and will not seal. The tap used after reaming must conform to the connection standard. The HSS tool is not intended for materials hardened above 40 HRC.
Taper ratio 1:16 — what it means in practice
a shallow taper for an NPT pipe thread
A taper ratio of 1:16 means that for every 16 mm of length, the diameter increases by 1 mm (in imperial units: 3/4 inch per foot). This is a shallow taper — to the naked eye, the tool looks almost cylindrical. Along the 45-millimeter cutting section, the diameter increases from Ø 43 mm at the tip (d₁) to Ø 45.8 mm at the base (d₂); the included taper angle is just 3.58°. NPT threads have the same taper — so the reamer prepares the hole precisely for this profile.
Frequently asked questions
Drill the pilot hole with a drill diameter close to the reamer tip diameter, approximately 42.8 mm (just under 43 mm). This allows the reamer to produce a 1:16 taper over its entire 45 mm flute length. If tapping without a reamer, use a larger 1-23/32" drill bit (≈ 43.7 mm) — the tap then forms the taper itself.
Yes. All three threads have the same taper 1:16, and the reamer only produces this taper. The thread profile (NPT and NPTF 60°, Rc 55°) is subsequently formed by the tap. However, finished NPT and Rc/BSPT connections are not interchangeable.
In a cylindrical hole, a taper pipe tap would have to form the taper and cut the thread simultaneously, significantly increasing torque and loading the first threads. Preliminary reaming reduces cutting resistance, improves thread concentricity and sealing, and extends tap life — especially in thick-walled housings and harder steels.
The version HSS (grade M2) works well in structural and carbon steel, cast iron, and nonferrous metals (brass, bronze, aluminum) — typical materials for valve bodies. In stainless steel and difficult-to-machine alloys, the cobalt version offers longer tool life HSS-Co (M35). Work by hand, steadily, using tapping oil; HSS is not intended for materials hardened above 40 HRC.
Product accessories
HSSE 17.5 cobalt metal drill bit DIN 338
Reference: 13297 In stock > 10 items
€17.11
€21.04 brutto
Machine tap NPT 1/2-14 DIN 374 C HSSE
Reference: 0000006496 In stock < 10 items
€84.21
€103.58 brutto
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
Viewed products
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.