Net price: €35.53
Description
| Technical data | |
|---|---|
| Nominal diameter d1 mm | M7 |
| Thread pitch P mm | 0.75 mm |
| Overall length l1 | 50 mm |
| Flute length l2 | 14 mm |
| Shank diameter d2 | 6.0 mm |
| Square drive size a | 4.9 mm |
| Tap drill diameter | 6.2 mm |
| Thread angle G | 60° |
| Tap tolerance | ISO2 6H |

Division of work in the 1–2 set
The M7x0.75 LH thread is cut into the wall of a hole with a diameter of 6.2 mm. The thread groove extends 0.4 mm into the wall. A single tap would have to cut the entire groove at once — by hand, this means high resistance and a risk of breakage. The set divides this work into two passes.
The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 8 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.
| Tap | Chamfer | Chamfer angle | Material removed | How it works in the hole |
|---|---|---|---|---|
| No. 1 – roughing tap | long, 8 threads | 5° | the main portion of the groove | enters smoothly and establishes thread alignment |
| No. 2 – finishing tap | short, 2 threads | 20° | the remainder, to the full profile | follows the cut threads and produces the full 6H profile |
The chamfer on No. 1 is 4 times as long as the chamfer on No. 2 — the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.
Hand tapping step by step
Drill bit 6.2 mm
Chamfer 8 threads
Chamfer 2 threads
Tolerance 6H
Turning sequence: half a turn counterclockwise, a quarter turn clockwise | Between taps: remove chips from the hole
Start with the hole. The drill diameter is easy to calculate: thread diameter 7 mm minus pitch 0.75 mm gives 6.25 mm — in practice, use a 6.2 mm drill bit. An undersized hole is a common cause of a tap twisting off in the workpiece.
The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 17.5 mm, or 2.5 times the thread diameter (2.5 x 7 mm, shown as 2.5D in the drawing). Drill the hole deeper than the thread. The finishing tap has a chamfer spanning 2 threads, so approx. 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates them along with the chips.
Fit the roughing tap into a tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. This is a left-hand thread, so turn in the opposite direction to usual: half a turn counterclockwise, then a quarter turn clockwise. Reversing breaks the chip into short pieces — a slight crunch is normal. The first threads determine whether the thread will be straight.
Unscrew the roughing tap and remove chips from the hole. Screw the finishing tap by hand into the cut threads — it should engage them naturally. Continue with the same turning sequence as for the roughing tap. The finishing tap removes the remaining material and cuts the groove to its full profile within 6H tolerance. Once it screws smoothly all the way in, the thread is complete — check it with an M7x0.75 LH screw.
M7x0.75 hand tap left-hand fine-pitch HSS from the well-known Fanar brand. This Polish company's products are used in virtually every branch of industry worldwide. They are valued for their exceptionally high quality, relatively low prices, and long service life. Our offered M7x0.75 hand taps left-hand versions are used for cutting metric fine threads with a 60° angle, ISO DIN-13, type M, 7 x -0.75. They can tap through holes and blind holes. The set includes two taps: a roughing tap with a 8P chamfer and a finishing tap with a 2P chamfer. They are made from modern high-speed steel (HSS), whose properties directly translate into extensive machining capabilities. Above all M7x0.75 hand taps left-hand versions resist potential damage when machining hard materials, enable significantly increased cutting productivity, and also provide high working precision. The tools are suitable for machining materials in classes P1.2 – P1.3. They comply with DIN 2181, with a tolerance class of 6H.
No customer reviews for the moment.
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Użyj strzałek, aby zmieniać zdjęcia. Powiększaj przyciskami albo gestem szczypania. Zamknij galerię klawiszem Escape.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.