• 98% satisfied customers
  • 72h delivery
  • 30 dni na zwrot
Hand Tapping M75x1.5 left-handed HSS - Varel
search
  • Hand Tapping M75x1.5 left-handed HSS - Varel
  • Hand Tapping M75x1.5 left-handed HSS - Varel - nr. 1
Varel

Hand Tap M75x1.5 LH DIN 2181/2 HSS Varel

Varel Varel
15068
€566.45 tax inc.

Net price: €460.53

Instant Shipping
W magazynie: 4 pcs.
W magazynie: 4 pcs.

Instant Shipping

Call and order: (44) 755-04-05

Description

Technical data for the M75x1.5 left-hand fine-thread hand tap

Technical data
Nominal diameter d1 mm M 75
Thread pitch P mm 1.5 mm
Overall length l1 160 mm
Flute length l2 37 mm
Shank diameter d2 50 mm
Square drive size a 39 mm
Tap drill diameter 73.5 mm
Thread angle G 60°
Tap tolerance ISO2 6H
Fine-thread taps drawing

Roughing tap and finishing tap – how much material each removes

Division of work in the 1–2 set

The M75x1.5 LH thread is cut into the wall of a hole with a diameter of 73.5 mm. The thread groove extends 0.75 mm into the wall. A single tap would have to cut the entire groove at once — by hand, this means high resistance and a risk of breakage. The set divides this work into two passes.

Tapping an M75x1.5 LH hole: 73.5 mm hole, tap No. 1 and No. 2 in a plate cross-section
Tapping an M75x1.5 LH hole: 73.5 mm hole, tap No. 1 and No. 2 in a plate cross-section

The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 8 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.

TapChamferChamfer angleMaterial removedHow it works in the hole
No. 1 – roughing taplong, 8 threads5°the main portion of the grooveenters smoothly and establishes thread alignment
No. 2 – finishing tapshort, 2 threads20°the remainder, to the full profilefollows the cut threads and produces the full 6H profile

How to distinguish the taps in the set

The chamfer on No. 1 is 4 times as long as the chamfer on No. 2 — the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.

How to tap an M75x1.5 LH hole – sequence 1, 2

Hand tapping step by step

Thread M75x1.5 LH in four steps

ØDrilling

Drill bit 73.5 mm

1Roughing tap

Chamfer 8 threads

2Finishing tap

Chamfer 2 threads

✓Finished thread

Tolerance 6H

Turning sequence: half a turn counterclockwise, a quarter turn clockwise | Between taps: remove chips from the hole

Start with the hole. The drill diameter is easy to calculate: thread diameter 75 mm minus pitch 1.5 mm gives 73.5 mm. An undersized hole is a common cause of a tap twisting off in the workpiece.

Through hole or blind hole – how deep to drill

The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 187.5 mm, or 2.5 times the thread diameter (2.5 x 75 mm, shown as 2.5D in the drawing). Drill the hole deeper than the thread. The finishing tap has a chamfer spanning 2 threads, so approx. 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates them along with the chips.

M75x1.5 LH thread in a through hole and a blind hole – cross-sections showing chip and chamfer clearance

No. 1 – the roughing tap establishes thread alignment

Fit the roughing tap into a tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. This is a left-hand thread, so turn in the opposite direction to usual: half a turn counterclockwise, then a quarter turn clockwise. Reversing breaks the chip into short pieces — a slight crunch is normal. The first threads determine whether the thread will be straight.

No. 2 – the finishing tap produces the full profile

Unscrew the roughing tap and remove chips from the hole. Screw the finishing tap by hand into the cut threads — it should engage them naturally. Continue with the same turning sequence as for the roughing tap. The finishing tap removes the remaining material and cuts the groove to its full profile within 6H tolerance. Once it screws smoothly all the way in, the thread is complete — check it with an M75x1.5 LH screw.

Set of M75x1.5 Left-Hand Fine-Thread Hand Taps

M75x1.5 Left-Hand HSS Hand Tap is a set 2-piece for manually cutting a metric fine profile with a diameter of 75 mm, where using a fine-thread tap in the left-hand version ensures precise profile formation with controlled torque.

Key specifications: nominal diameter 75 mm, pitch 1.5 mm, LH (left-hand) direction, HSS material; 60° metric profile. Set: starter tap No. 1 with a longer chamfer for stable guidance and finishing tap No. 2 for final shape and surface roughness. Recommended tap drill hole: 73.5 mm (D minus pitch) with a light entrance chamfer; as a left-hand tap it operates stably in through and blind holes. Recommended materials: structural and alloy steels, cast irons, copper and its alloys, and aluminum with suitable lubrication.

  • Axial alignment control — dividing the work into two stages reduces the risk of misalignment and improves conformity to the 60° profile.
  • Stable cutting performance — the longer chamfer on No. 1 reduces instantaneous torque, while No. 2 ensures uniform final cutting of the profile.
  • Higher dimensional repeatability — a 73.5 mm tap drill hole and axial guidance help achieve internal thread class 6H.
  • Reduced susceptibility to chipping — HSS tap maintains edge sharpness during manual operation, contributing to longer set life.

The configuration of 2-piece with distributed cutting loads promotes clean geometry and controlled profile roughness, maintaining stable assembly characteristics with a fine pitch of 1.5 mm.

Frequently asked questions

This is a 2-piece set: No. 1 (starter) stabilizes guidance and forms the initial profile, while No. 2 (finishing) produces the final profile and surface roughness; use them in sequence 1 → 2.

Yes, provided that clearance is left at the bottom of the hole for the leading section; the finishing stage has a shorter chamfer, making it easier to cut to the required depth.

Product accessories

Reviews

No customer reviews for the moment.

Add a review about the product

Hand Tap M75x1.5 LH DIN 2181/2 HSS Varel

Hand Tap M75x1.5 LH DIN 2181/2 HSS Varel

Shipping

All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE

Courier GLS Przelew24 / Prepayment 14,76 zł gross Delivery time 1 working day
Courier GLS Cash on delivery 17,26 zł gross Lead time 1 working day

This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

More information