Description
| Technical data | |
|---|---|
| Side length l | 12.9 mm |
| Insert thickness s | 4.76 mm |
| Hole diameter d1 | 5.5 mm |
| Corner radius rε | 0.4 mm |
| ANSI code | CCMT 431 |

finishing and semi-finishing — ISO groups P and M
| Material | Finishing | Semi-finishing | ||||
|---|---|---|---|---|---|---|
| Vc [m/min] | Feed f [mm/rev] | ap [mm] | Vc [m/min] | Feed f [mm/rev] | ap [mm] | |
| PSteel | 130-200 | 0.05-0.15 | 0.1-1 | 130-200 | 0.12-0.21 | 0.5-3 |
| MStainless steel | 70-100 | 0.05-0.15 | 0.1-1 | 70-100 | 0.12-0.21 | 0.5-3 |
single-sided 80° diamond with a hole and chip breaker
The CCMT 120404 turning insert is a single-sided, rhombic indexable insert made of grade H6310 cemented carbide, designed for turning steel and stainless steel. The C shape, a rhombus with a corner angle of 80°, combines cutting edge strength with good access to contours during longitudinal turning, facing, and light profile turning. Positive geometry with a 7° clearance angle (letter C in the designation) reduces cutting resistance, so the insert performs well on slender shafts and when boring small diameters. The nose radius rε of 0.4 mm favors finishing and semi-finishing, providing low surface roughness at moderate feed rates. The mounting hole with a single-sided chip breaker (type T according to ISO 1832) controls chip flow and breaking on the working side of the insert.
The CCMT 120404 insert (also written without spaces as ccmt120404) is suitable for turning shafts, bushings, and flanges made of structural steels, as well as stainless steel components, and its positive geometry also performs well in small-diameter boring bars. Calculate spindle speed using n = 1000·Vc/(π·D): for a shaft diameter of 40 mm at Vc = 180 m/min, the result is approximately 1432 rpm. For stainless steels, maintain a cutting speed of 70–100 m/min and a constant feed rate to limit work hardening of the layer being cut and remove heat from the small contact zone. Grade H6310 indexable inserts are supplied by the Korean brand Horn, and the PVD coating allows a single insert type to handle both ISO P and M groups. Reserve the 0.4 mm radius for finishing — for heavier passes and higher feed rates, choose the CCMT 120408 version with a nose radius rε of 0.8 mm. These two inserts differ only in nose radius; the remaining pocket dimensions are identical, so both fit the same holders.
Grade H6310 is not intended for steels hardened above 45 HRC — for hard turning, choose an insert with a cubic boron nitride cutting edge (CBN). Reserve the small nose radius rε of 0.4 mm for finishing; use a larger radius for roughing and interrupted cutting.
how to read the CCMT 120404 code — designation positions 1–7
Designation CCMT 120404 according to the standard ISO 1832: 4 letters describe geometry and construction, 3 numeric codes describe dimensions. Each field has a number, an icon, and a brief description.
ISO 1832 designation decoder — how to read the code
Positions 1–4 · ISO code
1CShape
80° rhombus
2 corners of 80° per side
2CClearance angle
α = 7°
positive, single-sided
3MTolerance
Class M (intermediate)
IC ±0.08 · thickness ±0.13 mm
4TType
Countersunk hole + chip breaker
countersink 40–60°, single-sided chip breaker
Positions 5–7 · dimensions [mm]
512Size
l = 12.9 mm
IC = 12.7 mm · 1/2″
604Thickness
s = 4.76 mm
between rake faces
704Corner radius
rε = 0.4 mm
code ÷ 10 → radius in mm
✓ 2 corners × 1 side = 2 cutting edges
holders with a 12 diamond-shaped pocket — external and internal turning
use, turning tool selection, and turning parameters
Two — the 80° diamond has 2 acute corners suitable for turning, and the positive geometry (7° clearance angle) makes the insert single-sided, with only the top surface used for cutting. Once one corner is worn, index the insert in its pocket to use the other.
Holders with a size 12 rhombic insert pocket (IC 12.7 mm): for external turning SCLCR/L (entering angle 95°), SCACR/L (90°) and SCMCN (50°) in cross sections from 16×16 to 25×25 mm; for internal turning, boring bars S25S–S40U with the suffix SCLCR/L or SCFCR/L. The full list is provided in the compatible turning tools section above.
Only in corner radius: 0.4 mm is used for finishing and semi-finishing at low feed rates, while 0.8 mm better withstands heavier passes and higher feed rates. The remaining dimensions (IC 12.7 mm, side length 12.9 mm, thickness 4.76 mm) are identical, so both inserts fit the same holders.
Yes — grade H6310 covers group ISO M20-M40. Maintain a cutting speed of 70–100 m/min, a constant feed, and continuous emulsion cooling: austenitic steel conducts heat poorly and work-hardens when cutting is too slow.
Reference: 0000004457 In stock > 10 items
€7.12 brutto
No customer reviews for the moment.
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Użyj strzałek, aby zmieniać zdjęcia. Powiększaj przyciskami albo gestem szczypania. Zamknij galerię klawiszem Escape.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.