• 98% satisfied customers
  • 72h delivery
  • 30 dni na zwrot
Hand Tap M8 HSS left - Fanar 2 piece
search
  • Hand Tap M8 HSS left - Fanar 2 piece
  • Hand Tap M8 HSS left - Fanar 2 piece - nr. 1
Fanar Narzędzia

Hand Tap M8 LH DIN 352/2 6H HSS

Fanar Narzędzia Fanar Narzędzia
377318
Thread size: M84 sizes of this tap
€11.01 tax inc.

Net price: €8.95

Brak w magazynie
Brak w magazynie

Call and order: (44) 755-04-05

Description

Material HSS
Thread size M8 left
Number of pieces2 pcs
Tolerance 6H ISO2

Technical data for the M8 left-hand hand tap

Technical data
Thread Diameter d1 M8
Thread Pitch P 1.25 mm
Overall Length l1 63 mm
Flute Length l2 20 mm
Shank Diameter d2 6 mm
Square Drive Width Across Flats a 4.9 mm
Tap Drill Hole 6.8 mm

Roughing tap and finishing tap – how much material each removes

Division of work in the 1–2 set

The M8 x1.25 LH thread is cut into the wall of a hole with a diameter of 6.8 mm. The thread groove extends 0.6 mm into the wall. A single tap would have to cut the entire groove at once – by hand, this creates high resistance and a risk of breakage. The set divides this work into two passes.

Tapping an M8 LH hole: 6.8 mm hole, tap No. 1 and No. 2 shown in a plate cross section
Tapping an M8 LH hole: 6.8 mm hole, tap No. 1 and No. 2 shown in a plate cross section

The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 8 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.

TapChamferChamfer angleMaterial removedHow it works in the hole
No. 1 – roughing taplong, 8 threads5°the main portion of the grooveenters smoothly and establishes thread alignment
No. 2 – finishing tapshort, 2 threads20°the remainder, to the full profilefollows the cut threads and produces the full 6H profile

How to distinguish the taps in the set

The chamfer on No. 1 is 4 times as long as the chamfer on No. 2 — the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.

How to tap an M8 LH hole – sequence 1, 2

Hand tapping step by step

Thread M8 x1.25 LH in four steps

ØDrilling

Drill bit 6.8 mm

1Roughing tap

Chamfer 8 threads

2Finishing tap

Chamfer 2 threads

✓Finished thread

Tolerance 6H

Turning sequence: half a turn counterclockwise, a quarter turn clockwise | Between taps: remove chips from the hole

Start with the hole. The drill diameter is easy to calculate: thread diameter 8 mm minus pitch 1.25 mm gives 6.75 mm — in practice, use a 6.8 mm drill bit. An undersized hole is a common cause of a tap twisting off in the workpiece.

Through hole or blind hole – how deep to drill

The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 20 mm, or 2.5 times the thread diameter (2.5 x 8 mm, shown as 2.5D in the drawing). Drill the hole deeper than the thread. The finishing tap has a chamfer spanning 2 threads, so approx. 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates them along with the chips.

M8 LH thread in a through and blind hole – cross-sections with clearance for chips and the chamfer

No. 1 – the roughing tap establishes thread alignment

Fit the roughing tap into a tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. This is a left-hand thread, so turn in the opposite direction to usual: half a turn counterclockwise, then a quarter turn clockwise. Reversing breaks the chip into short pieces — a slight crunch is normal. The first threads determine whether the thread will be straight.

No. 2 – the finishing tap produces the full profile

Unscrew the roughing tap and remove the chips from the hole. Screw the finishing tap into the cut threads by hand – it should engage them naturally. Continue turning with the same rhythm used for the roughing tap. The finishing tap removes the remaining material and cuts the groove to the full profile in tolerance class 6H. When it screws in smoothly all the way, the thread is complete – check it with an M8 LH screw.

M8 left-hand HSS hand tap DIN 352 – 2-piece set for left-hand threads

The M8 left-hand hand tap set is a practical set of two tools for cutting left-hand internal threads with a diameter of 8 mm and a pitch of 1.25 mm. The two-piece set of M8 left-hand HSS hand taps conforming to DIN 352 includes a roughing tap and a finishing tap, enabling fast tapping while maintaining the required quality. M8 left-hand threads are frequently used in rotating mechanisms and drive systems.

Key benefits of the M8 left-hand tap set

  • 2-piece set (roughing and finishing taps) – cutting in two stages speeds up tapping
  • M8 left-hand thread – prevents loosening in spindles, axles, and rotating components
  • HSS high-speed steel – versatile machining of steel, aluminum, and cast iron up to 800 MPa
  • Tolerance 6H according to DIN 352 – a precise fit with M8 left-hand screws of tolerance class 6g
  • Economical two-piece version – sufficient for materials of standard hardness

The M8 left-hand hand tap set is suitable for machine service centers, machine shops, and maintenance departments. To drill the hole for an M8 left-hand thread, use a drill bit with a diameter of 6.8 mm. Tapping direction – counterclockwise.

Tolerance 6H — metric thread tolerance classes

ClassAccuracyApplicationStatus
4H / 4g High Precision connections, hydraulics —
6H / 6g Standard Machine building, general-purpose SELECTED
7H / 8g Low Large clearance, easy assembly —

6H = internal thread (nut, hole) | 6g = external thread (screw)

Frequently asked questions

For an M8 thread with a pitch of 1.25 mm, use a 6.8 mm drill bit. The hole diameter is the same for right-hand and left-hand threads.

Yes, a two-piece set is sufficient for mild steel and aluminum. A 3-piece set is better for harder materials.

M8 left-hand threads are used in angle grinders, drill spindles, and mechanisms where they prevent self-loosening.

Product accessories

Tap wrench No. 3

Reference: 085009 In stock > 10 items

€13.16

€16.18 brutto

Reviews

No customer reviews for the moment.

Add a review about the product

Hand Tap M8 LH DIN 352/2 6H HSS

Hand Tap M8 LH DIN 352/2 6H HSS

Shipping

All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE

Courier GLS Przelew24 / Prepayment 14,76 zł gross Delivery time 1 working day
Courier GLS Cash on delivery 17,26 zł gross Lead time 1 working day

This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

More information