Description
| Technical data | |
|---|---|
| Nominal diameter d1 | BSW 1 3/4-5 |
| Thread diameter | 44.45 mm / 1 3/4 in |
| Thread pitch P | 5 threads per inch / 5.08 mm |
| Overall length l1 | 160 mm |
| Flute length l2 | 58 mm |
| Shank diameter d2 | 36 mm |
| Square drive size a | 29 mm |
| Thread angle | 55° |
| Thread standard | BS 84 (Whitworth) |
| Tap drill hole | 39 mm |

Division of work in the 1–2–3 set
The BSW 1 3/4-5 thread is cut into the wall of a hole with a diameter of 39 mm. The thread groove extends 2.73 mm into the wall. A single tap would have to cut the entire groove at once, requiring high manual torque and risking breakage. The set divides this work into three layers.
The drawing shows the entire set in operation. All three taps have the same shank and the same length. They differ in chamfer length: No. 1 has a taper spanning 7–10 threads, while No. 3 spans only 1–2 threads. The detail views at the hole wall show how the thread groove deepens after each tap.
| Tap | Chamfer | Material removed | How it works in the hole |
|---|---|---|---|
| No. 1 – roughing tap | long, 7–10 threads | approx. 60% | enters smoothly and establishes thread alignment |
| No. 2 – intermediate | medium, 3–5 threads | approx. 30% | screws into the previously cut threads and starts cutting only deeper in the hole |
| No. 3 – finishing tap | short, 1–2 threads | approx. 10% + sizing | cuts smoothly and produces the full thread profile |
The chamfer is the tapered end of the tap. No. 1 has the longest chamfer and No. 3 the shortest – the difference is immediately visible when they are placed side by side. No. 1 and No. 2 have shallower thread profiles; only No. 3 has the full profile. The number can also be identified on the shank: No. 1 has one ring, No. 2 has two, and No. 3 has none. Keep the set together and always start with the roughing tap.
Hand tapping step by step
Drill bit 39 mm
Removes approx. 60%
Removes approx. 30%
Removes approx. 10%
Thread BSW 1 3/4-5
Turning sequence: half a turn clockwise, a quarter turn counterclockwise | Between taps: remove chips from the hole
Start with the hole. Inch thread pitch is specified in threads per inch, so first convert it to millimeters: an inch is 25.4 mm, and 25.4 : 5 threads = 5.08 mm. The BSW 1 3/4-5 thread diameter is 1 3/4 in, or 44.45 mm. The Whitworth profile has a thread height equal to 0.64 times the pitch, so the minor thread diameter is 44.45 mm minus 1.28 × 5.08 mm, or 37.94 mm. The 39 mm drill bit listed in the table is larger: the thread in the hole has approximately 84% of the full height, and the tap removes less material. An undersized hole is a common cause of taps twisting off in the workpiece.
The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to 66.7 mm, or 1.5 times the thread diameter (1.5 x 44.45 mm, shown as 1.5D in the drawing). Drill the hole deeper than the thread. The clearance below the thread accommodates chips and the finishing tap chamfer.
Fit the roughing tap in the tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. Turn half a turn clockwise, then a quarter turn counterclockwise. Reversing breaks the chip into short pieces – a slight crunch is normal. The first threads determine whether the thread will be straight.
Unscrew the roughing tap and remove the chips from the hole. Screw the intermediate tap into the cut threads by hand; it should engage them on its own. It turns easily at first and only starts cutting deeper in the hole. The finishing tap enters with almost no resistance and cuts the final few percent of the profile only at the end. When it screws in smoothly all the way, the thread is complete; check it with a BSW 1 3/4-5 screw.
No customer reviews for the moment.
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Użyj strzałek, aby zmieniać zdjęcia. Powiększaj przyciskami albo gestem szczypania. Zamknij galerię klawiszem Escape.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.