- 98% satisfied customers
- 72h delivery
- 30 dni na zwrot
Description
Technical data for the G 3/4 inch hand tap
| Technical data | ||
|---|---|---|
| Nominal diameter d1 inches/mm | G 3/4 in | 26.44 mm |
| Thread pitch P inches/mm | 14 threads per inch | 1.81 mm |
| Overall length l1 | 90 mm | |
| Flute length l2 | 22 mm | |
| Shank diameter d2 | 20 mm | |
| Square drive size a | 16 mm | |
| Tap drill diameter | 24.50 mm | |
| Form C chamfer | No. 1: 5P, No. 2: 2P | |
| Thread angle G | 55° | |
| Thread standard | BSP DIN ISO 228 | |
Roughing tap and finishing tap – how much material each removes
Division of work in the 1–2 set
The G 3/4 thread is cut into the wall of a hole with a diameter of 24.5 mm. The thread groove extends 0.97 mm into the wall. A single tap would have to cut the entire groove at once – by hand, this means high resistance and a risk of breakage. The set divides this work into two passes.
The drawing shows the entire set in operation. Both taps have the same shank and the same length. They differ in their chamfer, the tapered tip: No. 1 has a chamfer spanning 5 threads, while No. 2 spans only 2 threads. The detail windows at the hole wall show how the thread groove deepens after each tap.
| Tap | Chamfer | Chamfer angle | Material removed | How it works in the hole |
|---|---|---|---|---|
| No. 1 – roughing tap | long, 5 threads | 7° | the main portion of the groove | enters smoothly and establishes thread alignment |
| No. 2 – finishing tap | short, 2 threads | 20° | the remainder, to the full profile | screws into the previously cut threads and produces the full thread profile |
How to distinguish the taps in the set
The chamfer on No. 1 is 2.5 times as long as the chamfer on No. 2 – the difference is immediately visible when you place them side by side. No. 1 has an incomplete thread profile; only No. 2 has the full profile. The number is also indicated on the shank: No. 1 has one ring, No. 2 has none. Keep the set together and always start with the roughing tap.
How to tap a G 3/4 hole – sequence 1, 2
Hand tapping step by step
Thread G 3/4 in four steps
ØDrilling
Drill bit 24.5 mm
1Roughing tap
Chamfer 5 threads
2Finishing tap
Chamfer 2 threads
✓Finished thread
Thread G 3/4
Turning sequence: half a turn clockwise, a quarter turn counterclockwise | Between taps: remove chips from the hole
Start with the hole. The G thread has a Whitworth profile, with a thread height of 0.64 times the pitch. The minor diameter of the internal thread is the 26.441 mm diameter minus twice the thread height, or 1.28 × the 1.814 mm pitch: the result is 24.117 mm. ISO 228-1 permits a hole diameter from 24.117 to 24.658 mm, and a 24.5 mm drill falls within this range. An undersized hole is a common cause of taps twisting off in the material.
Through hole or blind hole – how deep to drill
The set taps both types of holes. In a through hole, the thread extends through the full material thickness. In a blind hole, cut the thread to match the thread length of the fitting being installed. Drill the hole deeper than the thread. The finishing tap has a 2-thread chamfer, so approximately 2 incomplete threads remain near the bottom. The extra depth below the thread accommodates these along with the chips.
No. 1 – the roughing tap establishes thread alignment
Fit the roughing tap in the tap wrench and position it perpendicular to the surface. Check the angle from two sides, for example with a square. Turn half a turn clockwise, then a quarter turn counterclockwise. Reversing breaks the chip into short pieces – a slight crunch is normal. The first threads determine whether the thread will be straight.
No. 2 – the finishing tap produces the full profile
Back out the roughing tap and remove chips from the hole. Screw the finishing tap by hand into the previously cut threads – it should engage them naturally. Continue turning with the same rhythm used for the roughing tap. The finishing tap removes the remaining material and cuts the groove to its full profile. When it screws in smoothly all the way, the thread is finished – check it with a G 3/4 thread plug gauge: the GO end screws in by hand over the full length, while the NO-GO end enters no more than 2 threads.
3/4 inch G pipe hand tap
Hand Tap 3/4 inch G DIN 5157/2 HSS is a high-quality 2-piece set (roughing tap + finishing tap) designed for manually cutting G pipe threads (BSP – British Standard Pipe) o a profile angle of 55°. The tool is made from wear-resistant high-speed steel (HSS), providing long tool life, machining precision and reliability in workshop and installation work.
The 3/4 inch G thread has an external diameter of 26.441 mm, in accordance with ISO 228-1, and is widely used in water, gas and pneumatic systems. The designation DIN 5157/2 indicates that the tap is available as a 2-piece set – a roughing tap and a finishing tap – allowing safe, accurate thread cutting in stages.
Tap 3/4 inch G for pipes is a reliable tool for professionals working in installation, metalworking and industrial applications where compliance with BSP standards and high thread quality are essential.
- 2-piece set (DIN 5157/2) – roughing tap and finishing tap for manual use.
- G 3/4 inch thread – external diameter 26.441 mm (per ISO 228-1).
- 55° thread profile – compliant with the British BSP standard, ensuring leak-tight connections.
- HSS high-speed steel - high wear resistance and tool life.
- Manual applications – for precise tapping in water, gas and industrial systems.
Hand Tap 3/4 inch G is a proven choice for fitters, installers and metalworkers who value reliability and compliance with international technical standards.
Stages of cutting a G 3/4 inch thread with a 2-piece set: roughing and finishing taps
Frequently asked questions
The question “how many mm is G 3/4 inch” or “how many cm is G 3/4 inch” often arises when selecting pipe tapping tools. Contrary to what one might expect, the value 3/4 inch (equivalent to 26.4 mm or 2.64 cm) does not indicate the thread diameter, but the nominal size of the pipe that the thread fits. In practice, the G 3/4 inch tap has an outside diameter of 26.4 mm, because G (BSP) pipe threads are designed for thick-walled pipes.
For this reason, always check the thread diameter in the technical data instead of converting inches directly to millimeters. In the BSP system, thread size is determined by the design of the entire installation, not just the nominal dimension.
No. A G (BSP) thread is a parallel pipe thread, meaning its diameter is constant along its entire length. Unlike taper threads (designated R or BSPT), G threaded connections are not self-sealing. This means that a G thread does not provide a seal on its own – it requires an additional sealing element, e.g. a flat gasket, O-ring or plastic washer. This sealing method is commonly used in hydraulic, pneumatic and industrial installations.
Product accessories
Countersink 3/4 inch G HSS DIN EN 24231 Cztool
Reference: 000084
€25.79
€31.72 brutto
Out of stock
Metal drill bit 24.5 NWKc HSS DIN 345 Baildon
Reference: 0383 In stock > 10 items
€28.95
€35.61 brutto
Reviews
No customer reviews for the moment.
Shipping
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Recommended for you
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.
Cookie preferences
Functional cookiesTechnical
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Advertising Cookies
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.