Description
Technical data for a full-profile insert for trapezoidal threads with a 3 mm pitch
| Technical data | |
|---|---|
| Designation | 16 ER 3 TR MTA |
| Brand / part number | Horn / 15169 |
| Type | external threading insert, right-hand |
| Profile | full, trapezoidal Tr, 30° angle |
| Pitch | 3 mm |
| Profile height | 1.75 mm |
| Thread tolerance class | 7e |
| Insert size | 16: edge 16 mm, IC 9.525 mm |
| Cutting edges | 3 |
| Tool holders | right-hand external SER, size 16 |
| Grade | MTA: submicron carbide, PVD TiAlN |

Trapezoidal threading insert 16 ER 3 TR turns the full external thread profile with a 3 mm pitch: flanks, roots, and crests. It can cut threads from Tr 11 × 3 to Tr 60 × 3. It works in size 16 right-hand SER holders. It has three corners for use in succession.
The insert finishes the thread crests in the same cycle
The trapezoidal profile has a 30° flank angle and flat roots and crests. The external thread profile height h3 is 0.5 of the pitch plus the crest clearance ac = 0.25 mm, giving 1.75 mm. The insert turns the flanks, roots, and crests at the thread diameter in the same cycle.
The Tr 24 × 3 thread has a major diameter of 24 mm, a pitch diameter d2 = d − 0.5 × P = 22.5 mm, and a minor diameter d3 = d − 2 × h3 = 20.5 mm (PN-ISO 2904). Tolerance 7e is specified in the trapezoidal thread standard. Turn the shaft beforehand, leaving a small machining allowance. An undersized diameter will leave the crests unmachined and the profile too shallow. Check the finished thread with a thread ring gauge or a nut.
Feed of 3 mm per revolution and 8–17 progressively shallower passes
The shaft rotates while the insert advances along the axis by 3 mm per spindle revolution. In a typical setup, the right-hand insert feeds toward the chuck and cuts a right-hand thread. During the final passes, its side edges trim the crests to the thread diameter.
The insert reaches a depth of 1.75 mm in 8–17 passes; use 12 as a starting point. The first pass removes the most material; the final pass removes 0.05–0.08 mm. Use flank infeed at an angle slightly less than 15°, which is half the profile angle: the insert then cuts mainly on one flank.
At the end of the thread next to the shoulder, machine a runout groove at least 3.2 mm wide and at least 1.75 mm deep.
MTA grade is a submicron carbide with a PVD TiAlN coating for steel, stainless steel and cast iron. The speeds in the table apply to thread turning.
| Workpiece material | Cutting speed vc [m/min] |
|---|---|
| P Unalloyed steel, cast steel, free-cutting steel | 120–180 |
| P Low-alloy steel and cast steel (up to 5% alloying elements) | 80–130 |
| P High-alloy and tool steel | 60–80 |
| M Stainless steel and stainless cast steel | 90–130 |
| K Gray cast iron | 120–130 |
| K Ductile and malleable cast iron | 100–130 |
For each spindle revolution, the insert advances by one pitch: fn = P = 3 mm/rev.
Calculate the helix angle β using tan β = P / (π × d), where P is the pitch and d is the thread diameter. For Tr 24 × 3: 3 / (π × 24) = 0.040, giving β ≈ 2.28°. Standard threading holder shims tilt the insert by 1–1.5°. This thread has a larger angle, so select a shim with an inclination closer to 2.3° using the holder manufacturer's table.
One insert, many diameters with the same pitch
The pitch and tooth profile are independent of diameter. The profile height of a thread with a 3 mm pitch is always 1.75 mm, for both Tr 11 × 3 and Tr 60 × 3. The shaft being machined determines the thread diameter, not the insert.
The 16 ER 3 TR insert can cut trapezoidal threads listed in the PN-ISO 2902 table with a 3 mm pitch.
| Group according to PN-ISO 2902 | Thread sizes with a 3 mm pitch |
|---|---|
| Tr threadsPN-ISO 2902, pitch 3 mm | Tr 11Tr 12Tr 14Tr 22Tr 24Tr 26Tr 28Tr 30Tr 32Tr 34Tr 36Tr 38Tr 40Tr 42Tr 44Tr 46Tr 48Tr 50Tr 52Tr 55Tr 60× 3 |
Size, operating hand, pitch, profile and grade in the insert designation, holder selection
Size 16 indicates an edge length of 16 mm and an inscribed circle IC of 9.525 mm, or 3/8 inch; it is not the thread diameter. Dimensions X = 1.3 mm and Y = 1.5 mm specify the cutting tip position relative to the sides of the insert. The corner reproduces the trapezoidal profile: a 30° angle, a flat root, and crest clearance ac = 0.25 mm.
The insert profile matches a single pitch. At a different feed, the insert flanks will not align with the thread flanks, resulting in a distorted thread. An internal thread has a different depth and radii, so it requires an internal threading insert in an internal holder.
Mount the threading insert in right-hand external SER holders for size 16 inserts, e.g. SER 1616 H16, SER 2020 K16 or SER 2525 M16. A right-hand external insert works only in a right-hand external holder.
The 16 ER 3 TR trapezoidal threading insert finishes a trapezoidal thread with a 3 mm pitch, including the crests. A single insert can produce more than 20 sizes, from Tr 11 × 3 to Tr 60 × 3, always with the same profile height of 1.75 mm. It is suitable for lead screws and nuts with this pitch.
Key information before selecting an insert
You can cut external trapezoidal threads with a 3 mm pitch from the PN-ISO 2902 table: from Tr 11 × 3 to Tr 60 × 3.
Yes. The full profile cuts the thread crests at the major thread diameter, for example 24 mm for Tr 24 × 3. Simply turn the shaft beforehand, leaving a small machining allowance.
The profile height is 0.5 of the pitch plus the crest clearance ac: 1.5 + 0.25 = 1.75 mm (PN-ISO 2904). It is the same for every diameter with this pitch.
Right-hand external SER holders for size 16 inserts, e.g. SER 1616 H16, SER 2020 K16, SER 2525 M16 or SER 3232 P16.
Usually 8 to 17 passes; start with 12. For harder materials, add passes instead of increasing the cutting speed.
No customer reviews for the moment.
All orders are delivered by courier company GLS. For orders exceeding 369 PLN gross shipping is FREE
| Courier GLS | Przelew24 / Prepayment | 14,76 zł gross | Delivery time 1 working day |
| Courier GLS | Cash on delivery | 17,26 zł gross | Lead time 1 working day |
Użyj strzałek, aby zmieniać zdjęcia. Powiększaj przyciskami albo gestem szczypania. Zamknij galerię klawiszem Escape.
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.